LED T8 Tube Light

LED T8 Tube Light

Setting up LED tube lights is a great way to save loan on electricity and get possibly harmful fluorescent lights out of your home or office. However, most LED tube lights on the marketplace today can not just be straight set up in an existing fluorescent component. You will need to make some easy adjustments to the component to correctly install the bulbs. Fortunately is that setting up a LED T8 tube light in an existing fluorescent component is reasonably simple. In addition, you need to be able to purchase fixtures specifically developed for LED tube lights in the future, and they ought to really be cheaper than the comparable fluorescent fixtures. This article will offer a quick introduction describing exactly what you have to understand in order to install the new energy-saving fluorescent tube lights in an existing fluorescent lighting component.

Fluorescent fixtures are developed to support a particular types and size of fluorescent tube. A fluorescent tube is integrated into a fluorescent lighting system which consists of 2 or three primary elements: (1) the fluorescent light (fluorescent bulb or tube), (2) the ballast, and (3) the starter system. In addition, the system for a tube lamp consists of a light holder and a switch. Depending on the particular fluorescent lighting system, the starter may be a replaceable part, a starter might not be required, or the starter function might be integrated into the ballast. The starting function might also depend on the physical design of the fixture. To retrofit a fluorescent lighting fixture to support a LED T8 tube light, the ballast (and the starter if a different one is present) should be detached.

Make certain that the LED replacement tube lights are the appropriate size for the fixture. Also, constantly bear in mind that when servicing a fluorescent component or lamp for any factor, electrical power to the whole fixture should be disconnected. This is not constantly practical in situations where a large number of fixtures are managed from the same power control (such as in open workplace locations). In these cases, insulating gloves and a nonmetallic ladder need to be utilized if the fixtures must be serviced when power exists.

You will require a few simple tools, consisting of a wire cutter and wire stripper (often included into the same tool), a pair of pliers, a screwdriver, and a couple of wire nuts for reconnecting the wires as soon as you have actually removed the ballast.

When the old bulbs are removed from the lamp holders and the electrical power to the fixture is turned off, you will most likely need to eliminate the reflector that is located behind the bulbs and provides a real estate for the electrical wiring and ballast that lie behind it. Usually, it is relatively easy to get rid of the reflector or cover, however if it is not clear ways to do this, you need to speak with the paperwork from the component manufacturer.

If the fixture has an electronic ballast, you just need to eliminate that and after that wire the power directly to the light holders, finishing one circuit for each bulb. This is relatively easy, and generally you can utilize the existing wire in the fixture then simply add some wire nuts. If you have an older component with a magnetic ballast and starter, you will need to remove or open the starter and eliminate or short the magnetic ballast.

Depending on just how much wire you have to deal with, it is a great idea to leave enough time wires leading from the ballast to be able to reconnect the ballast with wire nuts, if you ought to ever want to convert the component back to utilize for fluorescent bulbs or want to utilize the ballast somewhere else. Normally, the ballast will have 2 screws or bolts holding it in location in the component, and these can be removed using a screwdriver or set of pliers, as proper. The ballast must be gotten rid of in accordance with regional regulations as must the old fluorescent bulbs. Since the fluorescent bulbs contain a small amount of highly-toxic mercury, they must be dealt with as contaminated materials and disposed of accordingly.


When the ballast (and starter, if one existed) have actually been gotten rid of and the wires reconnected to finish a circuit for each bulb, replace the reflector or cover over the electrical wiring and the location where the ballast was located, and the LED tube lights can be inserted in the end sockets. Unlike fluorescent bulbs which do not have a leading or bottom, a LED T8 tube light bought from www.edilig.com will have an obvious top and bottom, with metal heatsink situated on the backside of television and the LEDs visible under a lens on the side that will be aimed to the location to be brightened. Place the cover back on the fixture (if there was one) and switch on the electrical energy. Turn on the switch and if you have actually done everything properly, you must have as great or much better lighting using roughly half the electrical energy and lasting as long as 50,000 hours or more.